Search the Community

Hi Wanted to take my car to a garage so it could be checked and aligned. I don't know much about these things (caster , camber, toe etc...) I think 20 years old and never done this check/job right . Where i live in , i assume the tech. will have no idea how to set and to which measurements . are there any measurements / numbers/ guides for 1992 Gti?

Hi everyone, Something that has been bugging me for a while is the affect that having electrical devices turned on has on the idle on my 205. I know there will always be some impact but mine seems to suffer quite badly - for example, with the headlights on, heated rear window on and heater fan on half speed it will drop by as much as 4 or 500rpm on the rev counter depending on how warm the engine is and if the radiator fan has come on. I also find that if I press the brake pedal whilst the car is idling then this also drops the revs further and has led to stalling on the approach to junctions in the past. I wouldn't class these as extreme conditions (especially in winter) and I want to do some investigation to see if I have any faults or partial shorts that are causing a higher than necessary current draw. I've done loads of work on the air and fuel sides and the car idles really well now when there's no electrical load but I can't help but think that I'll see my old cutting out on the approach to junctions problems come back when I get out on the road at night or in the rain. At the minute I have the idle speed set slightly high (about 1100rpm on the rev counter when warm) to compensate but even so, when warm, if I turn a few devices on and press the brake pedal repeatedly it very nearly kills the engine. I do find that the affect is less pronounced when the engine is cold and the SAD is open (fast idle) but once the SAD closes (squeezing the pipe has no affect on idle) then the electrical impact on the idle gets worse. So, how do I go about testing all this? My first thought is to place my multimeter inline with the battery -ve terminal and the -ve clamp and measure the increase in current draw as various devices are turned on, make a note and see if there are any trends that appear by way of the circuits that devices are on and combinations of devices but I'm not sure if I should do this with the engine running (would this be dangerous/would I be risking blowing my meter?) as I don't want to flatten the battery by off and oning loads of devices for a day. I then think it might be a case of testing individual circuits by removing fuses and completing circuits with my meter to see if any circuits are drawing any/high current when the engine is off as this might give me clue as to a partial short but this is only what my common sense is telling me - any other ideas would be welcome please. Also, I don't really know what is an acceptable increase in draw for each device. The car doesn't blow fuses so I guess, if there is a/a combination of faults then I'm relying on subtle increases in the meter readings and I don't have any reference points - can anyone help me with this please? The one that really freaks me out the most is the brakes - however I'm not sure how applying the brakes might impact the idle outside of the electrical circuits associated with the brakes (lights etc.) any ideas would be welcome please as I can't assume that the drop in idle speed due to pressing the brake pedal is 100% electrical? I don't really understand how the brake system integrates into other systems that could affect the idle and I need to eliminate any other causes too so again, any help would be appreciated please. I should add that the alternator and battery are in good condition. The battery is a new 60ah battery and the alternator is from a 306 D Turbo - the voltage across the battery terminals is good regardless of the electrical load (14.8v when idling with no load, 14.3v with the headlights and fan heater on). Also, there is one unknown in that the idle/mixture screw hasn't been calibrated as yet - I have followed Damir's advice on here to achieve a ball park setting and this will be set up properly next Monday. The final piece of this puzzle is that although I do get good voltage across the battery terminals, the battery light on the dash does glow faintly if I use a lot of electrical devices when the car's idling. I also find that operating the electric windows seems to dim the dashboard lights. When holding the car at about 2.5k rpm, all of this goes away - the dash lights are unaffected by anything and the rpm stays constant regardless of what i turn on. After reading numerous other posts, I've made sure that the alternator exciter wire is good by watching the lights on the dash when starting and as far as I know all the earths are connected and in good order. I'd be really grateful for any pointers that could save me a bit of time chasing around the car with my meter please. It'll be a shame if I can't get this sorted after all the work I've done stabilising the idle as it does idle really smoothly now (until I turn a few bits on ) Many thanks in advance. Ian.