whizzer71 0 Posted March 20, 2008 Have noticed that DanPug has a set of TT pistons for sale but he says that they are for a 1.6 so I assume that the rods are different,would it just be a simple case of swapping the pistons onto 1.9 rods or are the pistons completely wrong for use in a 1.9 turbo application? Share this post Link to post Share on other sites
DamirGTI 342 Posted March 20, 2008 Hello ! Distance (mm.) from the the gudgeon pin center to the piston crown : 1.6 pistons : 37.5 1.9 pistons : 36.2 Yes the rods are different , the 1.6 ones are longer : 1.6 conrods : 150.5 1.9 conrods : 143 Anyway you can swap them , but be careful not to damage the piston as you need to press them out from the pistons and press back inside 1.9 ones ... Regards ! Damir Share this post Link to post Share on other sites
whizzer71 0 Posted March 20, 2008 Hello ! Distance (mm.) from the the gudgeon pin center to the piston crown : 1.6 pistons : 37.5 1.9 pistons : 36.2 Yes the rods are different , the 1.6 ones are longer : 1.6 conrods : 150.5 1.9 conrods : 143 Anyway you can swap them , but be careful not to damage the piston as you need to press them out from the pistons and press back inside 1.9 ones ... Regards ! Damir So would I be safe to use them in a turbo application? I want to run around 1 bar of boost without melt down in a otherwise std 1.9 Gti lump engine code D6B,emerald amangement TT manifold and a fair sized T25 or 28 turbo hoping for 200 + Bhp and enough torque to shift a small planet ! Will it work out and be reliable ?,or will it last 5 mins until I get to the nearest motorway and then blow a piston or melt a valve / valves ?? I have an RGX 2.0ltr turbo unit as well that I have been building but would prefer to stick with the 1.9 engine if at all possible ? Share this post Link to post Share on other sites
TEKNOPUG 3 Posted March 20, 2008 Standard pistons will be fine if you are using Emerald management and you have it mapped by someone that knows what they are doing. 1bar might be pushing it but in reality you won’t need to run that much boost to get the same figures as you would with lowered compression and increased boost. The engine will be more responsive too. Share this post Link to post Share on other sites
danpug 1 Posted March 20, 2008 Vern is running around 240 bhp on machined pistons, thats with an emerald. Share this post Link to post Share on other sites
whizzer71 0 Posted March 20, 2008 Standard pistons will be fine if you are using Emerald management and you have it mapped by someone that knows what they are doing. 1bar might be pushing it but in reality you won’t need to run that much boost to get the same figures as you would with lowered compression and increased boost. The engine will be more responsive too. On a D6B or DKZ engine,and is that totally std too or will I have to mod anything,I was thinking about using a Gti6 head gasket too just for abit of extra reliability Share this post Link to post Share on other sites
TEKNOPUG 3 Posted March 21, 2008 You want to use a 16v gasket for an 8v head an block........ Just use an 8v Grp N gasket from Peugeot - will be more than upto the job. Share this post Link to post Share on other sites
whizzer71 0 Posted March 25, 2008 You want to use a 16v gasket for an 8v head an block........ Just use an 8v Grp N gasket from Peugeot - will be more than upto the job. I thought the 8v & 16v gaskets were the same pattern and had the same oil feed/return holes etc ??? Share this post Link to post Share on other sites
guffe 2 Posted March 25, 2008 (edited) I thought the 8v & 16v gaskets were the same pattern and had the same oil feed/return holes etc ??? AFAIK the 8v and 16v gaskets are exactly the same, so there is no difference at the materials or reliability. Edited March 25, 2008 by guffe Share this post Link to post Share on other sites
welshpug 1,661 Posted March 25, 2008 AFAIK the 8v and 16v gaskets are exactly the same, so there is no difference at the materials or reliability. there is a difference, 1.9 ones are meant for an 83mm bore, 2.0 ones 86mm. Share this post Link to post Share on other sites
whizzer71 0 Posted March 26, 2008 I was originally toying wit the idea of turboing my original 1.9 engine as its low very mileage and like new inside I have a TT manifold coming and have a nice rebuilt T25 to put on it BUT I also have a 2.0ltr Turbo unit from a 406 that I have recently rebuilt IF I use the 2.0ltr engine then I will be using a GTI6 head gasket but IF I use the 1.9 I will be using a GRP N one,Dont really know which way to go right now and I'm sure that plenty of people have their own ideas / opinions . I have done several conversions using the 406 2.0ltr turbo engine with DKZ cam and raised boost with really good results, one of which gets driven to the absolute limit all the time and to be honest Im suprised that its survived dont know what its making at the wheels but its extremely rapid and pulls to the limiter in 5th with a hybrid gearbox (Diesel diff and a mix of 1.9Gti / Xsara Vts gears). So Im in the middle of decision time right now!,Do I stick with the tried and tested or try something new ? Share this post Link to post Share on other sites
