Jump to content
  • Welcome to 205GTIDrivers.com!

    Hello dear visitor! Feel free to browse but we invite you to register completely free of charge in order to enjoy the full functionality of the website.

Sign in to follow this  
GTI_E369

Gti front bumper slider kit..

Recommended Posts

GTI_E369

Hi all,

 

Apologies for this, as I know this topic has been raised beforehand, I've read a lot of other posts but want to check something. 

 

I've bought a 'complete slider and fitting kit' for my 205 but I want to check that I'm right in thinking the supplied t head bolts are wrong.

 

I've popped a couple of pics below, the problem i see is that the t bolts supplied, which allow the head to be flush in under the red stripe are far to long. In addition to this, the bolt isn't threaded all the way so unless something like another rubber bush bridges the gap it will never tighten up. My suspicion is the bolts supplied are for base models. 

 

I also have serious doubts over the reproduction of the slider it's self, which I know has also been discussed before hand, but you can see the difference in dimensions from the badly rusted original part.

 

Confirmation would be greatly appreciated before I respond to the company I got the kit from.

 

Thanks Gareth 

20240627_181906.jpg

20240627_181954.jpg

Share this post


Link to post
Share on other sites
Leslie green
Posted (edited)

There is a shorter T bolt for the Gti front yes , the original type ones still pop up on ebay or as part of the bumper fitting kit I think too .pics here on miami stu/ some of the non original T bolts don't fit /taper into the bumper that well as they are not bevelled either end . I would have though the sliders were fully tested before going into production and maybe its a quality control issue but unless people speak up to the seller with feedback then they may be unaware there is an issue.

 

https://www.miamistu.co.uk/pug/GB/205F/7/74A10A.HTM

Edited by Leslie green

Share this post


Link to post
Share on other sites
GTI_E369

Brilliant, thanks for confirming. I think my original slider brackets might go again, I'll get them sand blasted and see what's left,lol! 

 

In that diagram, it's the shorter t bolt '9' that looks to be required, I've seen Baker sell the shorter t bolts so think I'll get some and the bush with hex nut and fingers crossed the old brackets will go again. I've manged to knock the old rubber out this evening and had a little poke around of the brackets.

 

I'll send the ones I've bought back and get a refund.

 

Thanks again, help always massively appreciated. 

 

Gareth 

  • Like 1

Share this post


Link to post
Share on other sites
Dale

I might have a pair of the shorter t bolts left over from when I replaced my sliders earlier this year. I'll take a look tomorrow if it's any help to you?

Share this post


Link to post
Share on other sites
Dale

Took a  look in the shed this morning.

These are the ones I have left over.

I never tried fitting them as I went for the full kits from baker in the end.

I'm not sure where I got them from either sorry.

I believe the longer ones are for the rear just put them for comparison.

IMG_20240628_112527.jpg

IMG_20240628_112520.jpg

Share this post


Link to post
Share on other sites
GTI_E369
On 6/28/2024 at 11:35 AM, Dale said:

Took a  look in the shed this morning.

These are the ones I have left over.

I never tried fitting them as I went for the full kits from baker in the end.

I'm not sure where I got them from either sorry.

I believe the longer ones are for the rear just put them for comparison.

IMG_20240628_112527.jpg

IMG_20240628_112520.jpg

They look ideal, how much you wanting for the 2 short ones?

 

Thanks Gareth 

Share this post


Link to post
Share on other sites
Dale

Just postage mate. If you pm your address I'll send them down to you and let you know the cost if that's ok?.I'm not imagining it will anymore than a couple of quid. 

Share this post


Link to post
Share on other sites
GTI_E369

Brilliant, thanks again. Forgive my newbieness, I can't work out how to pm:ph34r:

 

Cheers Gareth

Share this post


Link to post
Share on other sites
Dale
19 minutes ago, GTI_E369 said:

I may be wrong on this but if I remember correctly just click on my name then hit the centre envelope symbol in the middle.

 

Screenshot_20240630_214151.jpg

Share this post


Link to post
Share on other sites
Tom Fenton

I don't think "Passenger" newer members with low post counts can PM? Its been a long time. I've been into the Admin screen but can't seem to change it for GTI_E369.

 

Maybe the solution for now is you guys exchange email addresses or phone numbers.

 

 

Share this post


Link to post
Share on other sites
Dale

Thankyou Tom, hope your keeping well?.

Gareth my email is, dalewebb@hotmail.co.uk

Share this post


Link to post
Share on other sites
GTI_E369
13 hours ago, Dale said:

Thankyou Tom, hope your keeping well?.

Gareth my email is, dalewebb@hotmail.co.uk

Hi Dale, just sent an email. 

 

Cheers,  Gareth 

Share this post


Link to post
Share on other sites
Dale

Got it gareth

Share this post


Link to post
Share on other sites
Dale

Posted these off to you today Gareth.

Sorry about the delay.

Share this post


Link to post
Share on other sites
GTI_E369
On 7/4/2024 at 1:58 PM, Dale said:

Posted these off to you today Gareth.

Sorry about the delay.

Awesome buddy, much appreciated. Will let you know when they arrive.

 

Thanks again, defo owe you a pint or 2.

 

Gareth 

Share this post


Link to post
Share on other sites
Dale

No worries Gareth. It was only a couple of quid so need to pay mate

  • Like 1

Share this post


Link to post
Share on other sites
GTI_E369
On 7/7/2024 at 11:05 AM, Dale said:

No worries Gareth. It was only a couple of quid so need to pay mate

Hi Dale, just to say the bolts arrived yesterday mate. As previous, thanks so much for this.

 

Cheers, Gareth 

Share this post


Link to post
Share on other sites
Dale

Good to hear they made it mate.

Happy to help

 

 

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
Sign in to follow this  

×