Jump to content
  • Welcome to 205GTIDrivers.com!

    Hello dear visitor! Feel free to browse but we invite you to register completely free of charge in order to enjoy the full functionality of the website.

Sign in to follow this  
flyfisher

Mi 16 Power Upgrade

Recommended Posts

flyfisher

Looking for a power upgrade for my 1905 alloy block mi16 in my cti would it be better to go with Webber 45s or a set of jenvey s itbs know the Webber route is the cheaper but in the long term is it the best

Share this post


Link to post
Share on other sites
dcc

Nothing cheap about webbers. Itbs all the way.

Share this post


Link to post
Share on other sites
Tom Fenton

If you just put bodies or carbs on don't expect a massive power increase. Maybe 10-15hp. The alloy Mi is pretty good as it is. Increased compression and cams needed along with bodies or carbs to really feel a big difference.

Share this post


Link to post
Share on other sites
Tom Fenton

Oh and also, (pedant mode on)

 

This is a Webber

 

4FBB9369-7D35-4CB8-8265-D503C7570318_zps

 

This is a Lloyd-Webber

A2845B8F-2F66-4B58-B68B-D378F41CCE99_zps

 

But THIS is a Weber (one B only)

 

761FB97E-A655-4C70-8714-C02674E031AD_zps

  • Like 2

Share this post


Link to post
Share on other sites
rallyeash

And one of them you wouldn't let your kids near...

Share this post


Link to post
Share on other sites
jackherer

Oh and also, (pedant mode on)

To be fair Weber is one of the most commonly misspelled words on car forums in my experience, second only to Dell'Orto. Or maybe carburetor/carburator/carburettor/carburetter (which is unforgivable given the four possible correct spellings.)

  • Like 1

Share this post


Link to post
Share on other sites
Simes

I got another 10bhp after adding Jenvey's, it also dialled out the lumpiness of the cams at idle.

It makes a terrific noise, on WOT I can be heard 2 miles away...............................

  • Like 1

Share this post


Link to post
Share on other sites
boldy205

NOTHING beats the sound od a side draught! :wub:

Share this post


Link to post
Share on other sites
Terry83

Guys I'm looking at both . The throttle bodies are a lot more in the long run , than carbs and more complex to set up , however don't need the maintenance of carbs ?

 

Unless there is a massive difference in fuel consumption and power out put I'm leaning towards the carbs 40's or 45's. What are your thoughts ? Thanks

Share this post


Link to post
Share on other sites
welshpug

its a massive difference in fuel usage, I know Sandy Brown's recent very high specification TU5 engine (230+bhp 1600) still does 40mpg, and pulls so hard from low and mid range.

Share this post


Link to post
Share on other sites
allanallen

My brother (calvinhorse) has a lightly tuned 8v on 45s, sounds amazing, goes well but does about 10mpg however you drive it.

Share this post


Link to post
Share on other sites
Simes

I've got jenveys and they use fuel, more so when you want it to make that noise.

 

Throttle bodies aren't any more complex than carbs. Each has there own characteristics. I'm more biased to bodies.

They aren't cheap, ecu, mapping etc.

 

What else has been done to your engine?

Share this post


Link to post
Share on other sites
Terry83

Mine nothing it's in bits at the moment .

I have an alloy 1.9 mi16 that I will be doing a full rebuild on

My friend is going down the carb road and so was I ?

Iv been offered a set of body's jenvey 45's and piper cams for £600

They come with gti6 injectors and fuel rails ?

Share this post


Link to post
Share on other sites
Simes

Snap them up.

 

You'll need an ECU and some other bits.....

 

look at my rebuild thread.

Share this post


Link to post
Share on other sites
calvinhorse

My brother (calvinhorse) has a lightly tuned 8v on 45s, sounds amazing, goes well but does about 10mpg however you drive it.

It's set up to run rich/safe so does use loads of fuel.. It's well worth it tho! The sound and the spluttering make it more novel to drive.

 

After 2 years of weekend driving the carbs have never caused any reliability problems, it starts easy, ticks over nice.. I'm in no rush to change to throttle bodies

Edited by calvinhorse

Share this post


Link to post
Share on other sites
Terry83

Are dhla40 carbs that will accompany the mi ?

Share this post


Link to post
Share on other sites
allanallen

40s aren't big enough, you'll need 45s.

Share this post


Link to post
Share on other sites
Terry83

But there the rite type just need bigger ones ?

Share this post


Link to post
Share on other sites
allanallen

You have to remember with carbs a 45 isn't actually a 45mm opening as they have 'chokes' in them which essentially make them smaller.

Share this post


Link to post
Share on other sites
Terry83

Iv been told 40's are better bottom end power ?

Share this post


Link to post
Share on other sites
petert

The number of gurus who can tune carbs is also rapidly diminishing. Definitely a dying breed. I'd suggest support for tb's and ecu's is far more common and cheaper.

Share this post


Link to post
Share on other sites
calvinhorse

I wouldn't say cheaper, I had my carbs setup at Mikeanics in Congleton for £180 (4 hours labour and emulsion tubes) you can probably get a map done for that but it won't be a good one :D

Share this post


Link to post
Share on other sites
Terry83

I agree if you can find someone who is good your away . But it's more reputation than anything else

Share this post


Link to post
Share on other sites
Terry83

Will 40's be big enough for the mi ,

I know 45's will give me more top end but there very hard to come by and expensive .

Will 40's be big enough for the mi ,

I know 45's will give me more top end but there very hard to come by and expensive .

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
Sign in to follow this  

×