Gti-6/ 406 V6 Wiring Diagram

[dave205 19]

Hi all, i havent been on here for ages, but im just starting some work on a project i started a year ago! Im after a wiring diagram/pucture of the 2 black round engine loom plugs with detail of what each pin corresponds to. Im also after the same for the commonly used 406 v6 engine, its the earlier d8 non multiplex engine from an s-reg coupe that i have. Any help appreciated!

[welshpug 1,657]

http://peugeot.mainspot.net/wiring406/index.shtml

 

that will get you a fair way with it given you are specifically interested in engine to car loom rather than engine itself.

 

1CO2A and 1CO2B on the second diagram are the two plugs.

 

23v is 23 way, or pins, MR and GR are the colour codes for the plugs.

 

 

worth reading this bit first as it explains a lot about the diagrams.

 

http://peugeot.mainspot.net/wiringall/index.shtml

 

 

 

engine specific diagram

 

[Goliath 94]

How old is that image Mei? ^^

 

I can't even remember the last time I used MSN messenger!

[omega 82]

don't suppose the op will care how old it is as long as it helps

[Goliath 94]

don't suppose the op will care how old it is as long as it helps

True

[welshpug 1,657]

I have no idea George, a very very old one I bet as I haven't used it since I got Facebook I'm sure! the next pic in the album is June 2009!

[dave205 19]

So that engine loom pic you've posted is for the 406 v6 engine loom?

 

Ive traced all the cables out on the 406 engine loom, from the red and grey round plugs that plug the engine loom in, back to each of the sensors etc on the loom, if you get me?

 

I just need to work out which pins on those plugs require earth, permanant live, switched live etc.

 

Also would anyone on here have a diagram or list of where each pin on the 306 round plugs go? And a list of which need earth, permanant live, switched live, as above really.

 

And finally, when the 496 engine was removed, the ignition was on and the ecu was un plugged, will this mean the ecu is unlocked? If so how do i prevent it re-immobilising?

[dave205 19]

Can anyone help? i still need to find out which pins on the engine plugs require earth, permanant live, switched live etc.

[welshpug 1,657]

Err, its all there for you.

[dave205 19]

Im not the best with drawings sorry :/

[welshpug 1,657]

not much more we can do but do it all for you then

[ade 4wd 11]

I take it your fitting the V6 engine into a 306. I do have details of the 2 round multiplugs on a 306 but need to know the year and engine as they vary a bit.

[dave205 19]

I take it your fitting the V6 engine into a 306. I do have details of the 2 round multiplugs on a 306 but need to know the year and engine as they vary a bit.

p-reg gti-6

 

not much more we can do but do it all for you then

lol would be nice

[ade 4wd 11]

Peugeot 306 GTI6 engine loom.

23 Pin round connector

1 - Ground

2 - Alternator warning lamp

3 - Reverse switch

4 - Reverse switch

5 - switched 12V

6 -

7 - Tachometer

8 - Starter motor

9 - "K" lamp

10 - Coolant high temp lamp

11 - Coolant gauge

12 - Oil pressure lamp

13 - Diag connector

14 - Oil level gauge

15 - Oil level gauge

16 -

17 - Diag connector

18 - Fuel pump

19 - Oil temp gauge

20 - Speedo

21 -

22 -

23 -

14 Pin round connector

1 - To brown temp sensor on engine if A/C fitted (controls rad fans)

2 - To brown temp sensor on engine if A/C fitted (controls rad fans)

3 - A/C

4 - A/C

5 -

6 - A/C

7 -

8 - Imob

9 - Imob

10 - Imob

11 -

12 -

13 -

14 -

NOTE: There is no constant 12V on either multiplug.

[dave205 19]

Does any one have a list like the one above ade's posted but for the 406v6 engine loom?

[welshpug 1,657]

yup, its on the first link I posted.

[dave205 19]

Cheers mate i havent read that for ages and had forgotten

[dave205 19]

Just been looking through that wiring diagram, it cant be for a v6 as it doesnt show to double relays

[ade 4wd 11]

That diagram isnt for the V6, however as Welshpug said it does show the pinouts for both 23 pin round connectors. They are IC02A and IC02B.

[dave205 19]

Yeah cheers ade ive done a bit more on the loom, forgotten how long it takes. Most of the sensors are connected, just need to make sure i put permanant and switched lives and earth to the correct remaining wires on the 406 loom. There is 25 cables left to go through :/. If i put power to any wire starting in bb the engine should run?