Part Number Wanted For Clutch Fork Bearings

[pugpete1108 62 1 Cars]

i went to my local pug yesterday for some release fork bearing top and bottom for my vts box.

 

he came out with two different sized ones parts 4 and 5 on this diagram.

 

now part 5 will in no way fit as my fork is the same dia all the way down?? and part 4 fits the shaft but does not fit the hole in the bellhousing as its too small ??

 

part 15 looks right for the bottom but what on earth do i use for the top???

 

its a be3 vts box im using

 

[welshpug 1,657]

these are the most common ones used -

 

2175 21 FORK BEARING

BA WHITE

2175 20 INF

BA WHITE

 

http://miamistu.co.uk/pug/GB/405N/2/20A25A.HTM

[Paul_13 212 1 Cars]

217520 1.26

217521 1.08

 

[pugpete1108 62 1 Cars]

neither of those show up on sb, but if you say they are right then i beleive ya.

 

but then i suppose being citroen items they wont can i order them from pug tho? or will i need to go to citroen

 

cheers guys.

 

pete

[Paul_13 212 1 Cars]

Pug mate, I've got them in my xsara box

 

[welshpug 1,657]

neither of those show up on sb, but if you say they are right then i beleive ya.

 

but then i suppose being citroen items they wont can i order them from pug tho? or will i need to go to citroen

 

cheers guys.

 

pete

 

oh yes they do

[pugpete1108 62 1 Cars]

oh yes they do

 

do they? where you put the part number then? i put it in the search bar and it said no parts

 

anyway no biggy just went down to pug and they had both in stock at a grand total of £3.03

 

cheers guys

 

pete

[Anthony 1,003]

Didn't look very hard then - those two part numbers are used on about half the Peugeot range on BE3 gearboxes when you search for them!

 

You are under Peugeot 205 1991 onwards aren't you? It's not listed in the Phase 1 / 1.5 section for some reason, even though the BE3 box was available in 1990.

[pugpete1108 62 1 Cars]

Didn't look very hard then - those two part numbers are used on about half the Peugeot range on BE3 gearboxes when you search for them!

 

You are under Peugeot 205 1991 onwards aren't you? It's not listed in the Phase 1 / 1.5 section for some reason, even though the BE3 box was available in 1990.

 

that would be why then, i was under ph1/1.5

 

didnt register that the be3 was a later box and yes it is listed under ph1 too

 

so i take it the search only works in the section you are in not the whole site?

[Anthony 1,003]

so i take it the search only works in the section you are in not the whole site?

It initially searches for the vehicle you've selected, and then there's a button to make it search under all models.

[smithy 1]

i went to my local pug yesterday for some release fork bearing top and bottom for my vts box.

 

he came out with two different sized ones parts 4 and 5 on this diagram.

 

now part 5 will in no way fit as my fork is the same dia all the way down?? and part 4 fits the shaft but does not fit the hole in the bellhousing as its too small ??

 

part 15 looks right for the bottom but what on earth do i use for the top???

 

its a be3 vts box im using

 

 

 

got 2 spare if you want them?

 

bottom one brand new the top one was fitted but replaced again after a month or so when i renewed the clutch fork,a bit birty but no wear on it.

 

PM me your address and i will drop them in post if interested?

[Miles 331 1 Cars]

Are you using the 205 arm? if so don;t forget there's 2 types, early and late but only way to check is to measure the fork length