Can Any-one Tell What This Box Is From

[tony perks 1]

Found what is supposed to be a partner gearbox, is it can you tell from these numbers?:

20T B10

then underneath ;88 32883a, also what diif would be in it?

[alync406 4]

I don't know about the numbers, but if it is from a Partner it should probably have a 4.53:1 ratio crown wheel/pinion. Is it a BE3 or BE4 gearbox? It is normally stamped int the casing somewhere near the mounting I think.

[welshpug 1,662]

I take it it is a BE box?

 

edit;

 

2205 WP

 

NEW MEC GEARBOX

CP 15X74- CT 22X19

 

TAG CH44 TB10 (TB1K)- BE3/5N2 AND REAR AXLE HYPOID GEARSET 15 X 74 AND TACHO TORQUE 22X19 UNTIL RPO No. 07916

 

4.933

 

DRIVEN PINION 1ERE 38DTS (11X38)

 

DRIVEN PINION 2EME 43 DTS (23X43)

 

DRIVEN PINION 3/4E (25X32)(41X39)

 

DRIVEN PINION 5EME 35DTS (47X35)- BE3/5N2

Edited September 27, 2010 by welshpug

[tony perks 1]

I take it it is a BE box?

 

edit;

 

2205 WP

 

NEW MEC GEARBOX

CP 15X74- CT 22X19

 

TAG CH44 TB10 (TB1K)- BE3/5N2 AND REAR AXLE HYPOID GEARSET 15 X 74 AND TACHO TORQUE 22X19 UNTIL RPO No. 07916

 

4.933

 

DRIVEN PINION 1ERE 38DTS (11X38)

 

DRIVEN PINION 2EME 43 DTS (23X43)

 

DRIVEN PINION 3/4E (25X32)(41X39)

 

DRIVEN PINION 5EME 35DTS (47X35)- BE3/5N2

so i should buy it then as i want a be3 4.8/9 cwp

[welshpug 1,662]

as long as you don't mind a silly first gear and a big gap to 2nd!

 

ratio's are as follows;

 

3.45 1.86 1.28 0.95 0.74

 

mph/1000 rpm - 4.0 7.4 10.7 14.4 18.5

[tony perks 1]

as long as you don't mind a silly first gear and a big gap to 2nd!

 

ratio's are as follows;

 

3.45 1.86 1.28 0.95 0.74

 

mph/1000 rpm - 4.0 7.4 10.7 14.4 18.5

 

 

Dont want the ratios just the cwp to go into my box!

[welshpug 1,662]

you have to have the 1st and 2nd, as they are machined into the pinion, that's why Quaife or Peugeot/Citroen Sport etc gearsets make more sense when you go this low on the gearing, it highlights the difference in gears somewhat when used for rallying.

Edited September 27, 2010 by welshpug

[alync406 4]

I have a 4.53 cwp in mine and 1st and 2nd were'nt machined into the pinion.I used the 205 1.9 GTi 1st and 2nd.It was a BE4 box though so maybe it is different, don't think it should be though.That box would not really be much use if they are.

[Miles 331 1 Cars]

Nope the Pinion is a plain shaft, Make sure it;s the early BE3 type as the later ones like Xsara's use a slightly longer shaft

[tony perks 1]

Nope the Pinion is a plain shaft, Make sure it;s the early BE3 type as the later ones like Xsara's use a slightly longer shaft

 

The box is cheap so i will take a chance, in the photo the guy has sent me it looks like a BE3. not a BE 4, also has the pull clutch soa bonus there, i have long since given up trying to find the right 3rd/4th gears to go with all the BE4 cwps i found so am trying to find the right CWP to fit my BE3, any how as i said i dont need the ratios from it just the CWP shaft and ring, well and some spare syncros wouldnt go amiss!