Where To Buy Head Bolts?

[asdf205 0]

Where can i get a set of head bolts for a s16 engine?? I have tried local dealer with no luck and not having much online either.

[M@tt 77]

any reputable motor parts place should be able to get you a set no problems. Contact your local GSF if not

[chrisj21 2]

I got mine for the vts from GSF. as M@tt says give your local one a call.

[S@m 156]

I have tried local dealer with no luck and not having much online either.

 

The dealers definetly do them, the part number is 0204.A0 i believe, they do cost more than a fiver each though so GSF might be the better option. But still, yet another example of pug dealers fobbing off people looking for parts that require a little bit of effort to find!

Sam

[asdf205 0]

Cant find them on the GSF website and there isnt one over here but ill give them a call and see if they will deliver.

[welshpug 1,666]

yes they do mail order, I got some recently for my gti6 engine, they use the same bolts on all the iron block 2.0 16v engines.

 

their website really is pretty crap regards the information it holds.

 

These are the correct bolts if their listing is correct - 011PC0120 CYLINDER HEAD BOLT SET 406 2.0 16V 15.50

 

the peugeot part number for them individually is as Sam posted up above, 204 A0

[asdf205 0]

Thanks i rang up and quoted that number and it was the correct one. They do deliver over here too so problem solved

Edited July 28, 2010 by asdf205

[asdf205 0]

Ordered the bolts from there now. I didnt realise they were star heads. What size heads are they and where can i order the socket from? I need a 1/2 inch drive.

 

I also need some of the studs that go into the head where the inlet manifold attaches to. GSF doesnt sell these. Is there anywhere else i can try?

[S@m 156]

Peugeot still do the studs, and unlike the headbolts they arent silly money. Isnt there just one though? (on the top right as you look at the engine), If thats the one you mean its part 6929.23 and is 71p +VAT, you might want to check that one though in case we have our wires crossed.

Sam

[asdf205 0]

No there is 8. 2 Per cylinder in a diagonal setup. Ill try and get a picture of the ones i mean.

 

Edit - The ones poorly circled in blue.

 

 

I also need 8 of the bolts circled in green if anyone has a part number?

Edited July 28, 2010 by asdf205

[S@m 156]

Oh, you mean the inlet manifold bolts, not the studs. There is one stud, as i have already mentioned. I believe the other 7 are bolts, their part number is 6913.96 and they are a quid or so each, its been a long time since i played with a 2.0 Mi/S16 though so the quantity of each might be a bit out, there is definetly at least one stud though. And the green circled ones you are after are no longer available from Peugeot, but they are just 25mm long M6 bolts so shouldnt be hard to find alternatives.

Sam

[asdf205 0]

So the one that is already there is a stud and the rest are bolts?

[S@m 156]

So the one that is already there is a stud and the rest are bolts?

 

Thats right, the bare thread that just screws into the block (its already there by the looks of it) and requires a nut is the stud, the others are bolts with the part number i mentioned already.

 

Sam

[asdf205 0]

Thats right, the bare thread that just screws into the block (its already there by the looks of it) and requires a nut is the stud, the others are bolts with the part number i mentioned already.

 

Sam

 

Ahh didnt realise that. Thanks. I did wonder why there was only one in there.

[S@m 156]

The exhaust manifold is a similar arrangement. Either way, did you manage to get the headbolts?

[asdf205 0]

My exhaust manifold is all studs and has these rounded locking nuts. Head bolts should be here tomorow. Next job is finding a socket to fit (read about some of them not being deep enough).

[M@tt 77]

I'm pretty sure it's a T55 Torx bit you need, i'm sure someone will correct me if it isn't

 

http://www.justoffbase.co.uk/T55-X-140mm-T...151%2C200%2C668

 

or just find a local draper stockist and they should be able to get you one no probs

Edited August 2, 2010 by M@tt

[asdf205 0]

Thanks. Ill give the Draper place a ring and see if they have one.

[asdf205 0]

Head bolts arrived today but they are the opposite head compared to the ones that came off. I now need a socket that fits around the outside rather then inside.

[welshpug 1,666]

E55 / female Torx, from memory is the size.

 

they probably look like this;

 

 

for which you'll need one of these.

 

Edited August 2, 2010 by welshpug

[asdf205 0]

That looks exactly like them (same box too). Thanks.