Mi16 4 Branch Donut Gasket

[matthewm 1]

As titled really - tryed local motor factors to match my old one although no joy - had Timax FDG40 suggested although was much to big, so if anyone had any part numbers for one or vehicle makes and models so I've got somewhere to start with the factors.

Appreciate they different makes of manifold are probably different sizes - my external at the widest is approx 74mm, and internal widest approx 56mm.

Thanks very much

[JeffR 51]

The fixing kit which includes the braided gasket, springs, bolts, etc is-1798 75.

[JeffR 51]

The fixing kit which includes the braided gasket, springs, bolts, etc is-1798 75.

 

^^^ Sorry that's for the 1.9 alloy engine.

 

The 2.0 litre part no is-1798 68.

[matthewm 1]

Cheers Jeff, its the 1.9 alloy, although the manifold is an aftermarket 4 branch, with the donut down under the car - is the gasket the same as the standard 405 gasket then? As the 405 one from the factors is not quite right.

[JeffR 51]

Hard to say if a std one will work with an aftermarket manifold, but my 1.9 Mi16 has a 4-2-1 PugRacing (Miles) mani & apparently uses a 'derv' gasket.

[welshpug 1,657]

IIRC DrSarty has the part number, its from an XV/XY engined 205 etc.

[DrSarty 90 1 Cars]

IIRC DrSarty has the part number, its from an XV/XY engined 205 etc.

 

I'll post up the number tomorrow for you/everyone.

[matthewm 1]

I'll post up the number tomorrow for you/everyone.

 

Thank you very much Dr S!

[DrSarty 90 1 Cars]

Here ya go.

 

 

[Alan_M 66 1 Cars]

Bringing this thread back from the dead, is that XV/XY donut for the PugRacing (Miles) types 4-2-1 Mi16 manifold?

 

And is that a Peugeot part number?

[Alan_M 66 1 Cars]

Can someone confirm this? My 205 is sounding like a bag of s*it......

[Alan_M 66 1 Cars]

Just to add a bit of info on this.....

 

Got this gasket from Camberley Auto Factors (part number PGG17). Its from a 306 1.9DT XUD9TE. Quite sure MyParts.co.uk do them too if you can wait for postage.

[matthewm 1]

Just to add a bit of info on this.....

 

Got this gasket from Camberley Auto Factors (part number PGG17). Its from a 306 1.9DT XUD9TE. Quite sure MyParts.co.uk do them too if you can wait for postage.

 

Did it fit well mate? Fitted one to mine, did the job but still wasn't a perfect match for my manifold!

[Simes 248 2 Cars]

Timax FDG30.

 

[Alan_M 66 1 Cars]

Did it fit well mate? Fitted one to mine, did the job but still wasn't a perfect match for my manifold!

 

The gasket wasn't as tight on the manifold as I'd like it to be, but it sounds so much better. I think it's now slightly blowing up at the Y piece now.

 

Timax FDG30.

 

 

Now you tell me......(are you sure, thats off a Carlton diesel)

[Simes 248 2 Cars]

The gasket wasn't as tight on the manifold as I'd like it to be, but it sounds so much better. I think it's now slightly blowing up at the Y piece now.

 

 

 

Now you tell me......(are you sure, thats off a Carlton diesel)

 

Sorry I meant FDG40

 

The FDG30 is for the new 'knuckle' I had made up.

[Anthony 1,002]

There seems to be various ones that fit - I know I used a Mondeo one IIRC which was a nice snug fit and worked a treat

[Jrod 7]

Sorry I meant FDG40

 

 

This is not correct for Miles manifolds. I ordered one and its huge!

 

Turns out I didn't need it anyway as its blowing because the exhaust has cracked.

Edited December 31, 2010 by Jrod

[yorkshirekowboy 19 1 Cars]

Can anybody confirm which donut gasket in the end they used for the 4-2-1 manifold y piece ?

 

PS sorry for bringing back the topic from the dead. Just wanted people's opinions of which donut gaskets they have used and been good etc.????

Edited February 24, 2016 by surferkid205

[Bakes100 20 1 Cars]

I ordered Timax reference part number:PGG17 from ebay, it fitted fine.

 

It has an internal diameter of 59mm.

 

Hope this helps

 

Stuart

[Simes 248 2 Cars]

I never got to the bottom of it.

I had a new piece of exhaust made up to join the manifold and centre box up which eradicated that gasket.

[yorkshirekowboy 19 1 Cars]

Just an update, I've tried the part number:PGG17 it's to tight, no way can you get it on whole. I've damaged the gasket trying to get it on. What a nightmare. What other donut rings have people tried and successfully completed there exhaust build?

[yorkshirekowboy 19 1 Cars]

Anybody?