PaulJLLD 0 Posted January 31, 2010 Hi As title, how have you mounted your cut off switch? Thanks Paul Share this post Link to post Share on other sites
Atari Boy 11 Posted January 31, 2010 (edited) I have just fitted one, I was planning on using a base model clock blanking plate but there was not enough space behind the panel. Instead I have used the tray area next to the lower console. I needed to 'adjust' the internals but is looks quite tidy. If it is of interest then I can get you a picture. I am sure there will be other places to use but I wanted it to be as OE as possible. Edited January 31, 2010 by Atari Boy Share this post Link to post Share on other sites
PaulJLLD 0 Posted January 31, 2010 I have just fitted one, I was planning on using a base model clock blanking plate but there was not enough space behind the panel. Instead I have used the tray area next to the lower console. I needed to 'adjust' the internals but is looks quite tidy. If it is of interest then I can get you a picture.I am sure there will be other places to use but I wanted it to be as OE as possible. Pic would be good to see what it looks like, iv got one to fit to my rally car this week and wondering what people have done. Thanks Share this post Link to post Share on other sites
Batfink 201 Posted January 31, 2010 do you need to be able to reach it with your harnesses on? Worth considering depending on whether you have moved the seat back or not. Share this post Link to post Share on other sites
pugpete1108 62 1 Cars Posted January 31, 2010 i made a whole new centre panel: Share this post Link to post Share on other sites
PaulJLLD 0 Posted January 31, 2010 do you need to be able to reach it with your harnesses on? Worth considering depending on whether you have moved the seat back or not. [/quote no i dont think so anyway Share this post Link to post Share on other sites
PaulJLLD 0 Posted January 31, 2010 What did you make the plate out of? Looks very tidy. Share this post Link to post Share on other sites
SurGie 54 Posted January 31, 2010 i made a whole new centre panel: I like the look of that, very tidy indeed. Share this post Link to post Share on other sites
pugpete1108 62 1 Cars Posted January 31, 2010 What did you make the plate out of? Looks very tidy. its actually a peice of lexan, i have just flatted and sprayed the rear side of it. Share this post Link to post Share on other sites
woo83 0 Posted January 31, 2010 I put mine where the heather controls were, Just turned the heater to demist and redirected power through a switch so the heater was either flat out or off. Share this post Link to post Share on other sites
Atari Boy 11 Posted January 31, 2010 Sorry, dark garage + crap iPhone camera = rubbish photo. With luck it will give you an idea, I can reach it with my harness on too. Share this post Link to post Share on other sites
hcmini1989 16 Posted February 1, 2010 Sorry, dark garage + crap iPhone camera = rubbish photo.With luck it will give you an idea, I can reach it with my harness on too. ive got mine the same as this and what a f***n ballache it was to get it in there ive got a starter switch next to it aswell Share this post Link to post Share on other sites
PaulJLLD 0 Posted February 1, 2010 ive got mine the same as this and what a f***n ballache it was to get it in there ive got a starter switch next to it aswell Thanks but i dont have that in the car, had to remive it to fit the hyd handbrake Share this post Link to post Share on other sites
Stu 18 Posted February 1, 2010 I mounted mine in the heater vent.... Easily reachable in the seat with harnesses on, complete twat to get it in though! Share this post Link to post Share on other sites