XU Engine & Gearbox Service and Maintenance - ARCHIVE

3,725 topics in this forum

1. Picture Of Timing Belt End Of 8v Engine

   By James_R, April 1, 2009
   • 10 replies
   • 4,616 views
   • 
   • James_R
   • April 6, 2009

2. Picture Required

   By murtaghp, April 22, 2011
   • 7 replies
   • 1,152 views
   • 
   • mikeygulley
   • April 26, 2011

3. Pin No For Rev Counter

   By harryskid, May 24, 2010
   • 3 replies
   • 1,000 views
   • 
   • ade 4wd
   • May 24, 2010

4. Pipe Under Throttle Housing With No Tube On It

   By splant, April 27, 2010
   • 5 replies
   • 956 views
   • 
   • splant
   • April 28, 2010

5. Pipe Washer (Firing Ring?)

   By chipstick, September 13, 2011
   • 3 replies
   • 778 views
   • 
   • chipstick
   • September 13, 2011

6. Piston Direction When Fitting

   • 1
   • 2

   By wardy18, April 21, 2009
   • 43 replies
   • 8,008 views
   • 
   • mattbenselin
   • April 26, 2009

7. Piston Liner Advice After Head Removal

   By martyn180, March 4, 2010
   • 7 replies
   • 5,604 views
   • 
   • floodys
   • April 18, 2010

8. Piston Liner Seals

   By smithy, June 3, 2011
   • 2 replies
   • 785 views
   • 
   • j_turnell
   • June 3, 2011

9. Piston Liners - Should The Be A Tight Fit?

   By XLR8, February 7, 2009
   • 3 replies
   • 1,438 views
   • 
   • XLR8
   • February 8, 2009

10. Piston Liners And Sealant?

    By madspikes, March 5, 2009
    • 6 replies
    • 1,695 views
    • 
    • mattmk1
    • March 5, 2009

11. Piston Protrusion

    By skinner2k3, June 28, 2010
    • 4 replies
    • 1,554 views
    • 
    • welshpug
    • June 28, 2010

12. Piston Rings On A Xu10J4Rs

    By cheesegrater, June 11, 2011
    • 4 replies
    • 1,026 views
    • 
    • Miles
    • June 13, 2011

13. Piston Xu9Ja And Xuj

    By Hroche, November 26, 2011
    • 4 replies
    • 1,200 views
    • 
    • Hroche
    • November 27, 2011

14. Pitting In "squish" Are On Cylinder Head

    By JoshGti, November 6, 2011
    • 6 replies
    • 1,612 views
    • 
    • JoshGti
    • November 8, 2011

15. Planning A Rebuild 1600 Gti-Blown Head Gasket Etc

    By Sinbad, October 3, 2011
    • 8 replies
    • 2,608 views
    • 
    • Sinbad
    • October 5, 2011

16. Plastic Inlet Manifold On 93/94 Gti..

    By gerry, September 20, 2012
    • 14 replies
    • 2,408 views
    • 
    • gerry
    • September 23, 2012

17. Plastic Lined Fuel Pipe

    By MerlinGTI, April 25, 2010
    • 0 replies
    • 666 views
    • 
    • MerlinGTI
    • April 25, 2010

18. Plastice 'housing' Near Thermostat

    By Obey_R, January 31, 2011
    • 2 replies
    • 1,024 views
    • 
    • pug_ham
    • January 31, 2011

19. Please Help

    By mattwalder, June 27, 2010
    • 18 replies
    • 2,738 views
    • 
    • quat-fro
    • July 18, 2010

20. Pointers For Dropping My Engine+subframe Please

    By Oberon, February 25, 2010
    • 3 replies
    • 895 views
    • 
    • j_turnell
    • February 25, 2010

21. Poor Fuel Economy

    By john-melbourne, May 2, 2012
    • 14 replies
    • 2,287 views
    • 
    • Teacher
    • August 28, 2012

22. Poor Fuel Economy - Gti-6

    By Joshy, December 19, 2009
    • 14 replies
    • 2,502 views
    • 
    • Joshy
    • December 24, 2009

23. Poor Running After Mods

    By 24seven, August 23, 2008
    • 12 replies
    • 2,821 views
    • 
    • 24seven
    • February 19, 2009

24. Poor Starting On 1.9 8V

    By matt1900, August 16, 2012
    • 3 replies
    • 1,414 views
    • 
    • matt1900
    • August 16, 2012

25. Possible Bent Valves

    By jaggers12, October 17, 2011
    • 9 replies
    • 1,041 views
    • 
    • jaggers12
    • October 21, 2011